幸运农场

联系我们

联系人: 刘经理 手机: 15953131568        18888346536 QQ: 408031499 网址:  地址: 济南市天桥区金牛建材市场

新闻中心当前位置:首页—新闻中心

济南卷帘门厂讲解正确的使用卷帘门设备
2015-4-9 14:10:33
随着卷帘门的不断发展,卷帘门设备的需求也有所变化。卷帘门设备是一种生产加工卷帘门的机械,机械在使用过程中都要非常注意,按照操作要求来操作,这样才能安全使用。怎样才能是正确的使用卷帘门设备呢?
With the development of rolling shutter door, rolling shutter door equipment needs change. Shutter device is a production and processing of rolling shutter machinery, machinery have to be very careful in the use of the process, operating in accordance with the requirements of operation, so as to safe use. How to use the shutter device is correct?
1、在卷帘门设备开机之前,必须先加满变速箱里的机油,液压站里加到60毫升液压油。
1, before the shutter device boot, must fill in the gearbox oil, add 60 ml of hydraulic station hydraulic oil.
2、在轧机气动之后,先把材料推入第一组轧轮,等材料到最后两组轧轮时,就要注意产品的形状是否符合要求,或者把螺丝调上或调下,直到调整到所需要的状态,才可以把螺丝固紧。济南卷帘门厂
2, after the mill pneumatic, put the material into the first group of rolling wheel, and other materials to the last two sets of rolling wheels, should pay attention to whether the shape of the product to meet the requirements, or the screw adjusted up or down, until the adjustment to the needs of the state, it can tighten the screw with a screwdriver.
3、在其启动轧机之前,假如齿轮和轧轮受到摩檫而损坏,是因为没在齿轮的上下轧轮处加润滑油,所以卷帘门机械在保养的时候,应该针对轧轮每1小时和齿轮每8小时,以及减速箱每半年加一次油。
3, before the start of the mill, if the gear and the rolling wheel by friction and damage, because no rolling wheel lubrication in gear, so the rolling shutter machinery in the maintenance, should according to the rolling wheel and gear every 1 hours, every 8 hours, and the gear box every six months once oil.
4、在工作前,首先把一些合适的材料放在导板上进行校正,等校正后方可工作,如果有脱扣的现象,说明压出的材料在左右偏移,可以通过进料导板上的左右摇动进料位置的方式,达到所压出合适的产品,最后把螺丝固紧。
4, before work, first put some suitable materials in the guide for correction, the correction before working, if tripping phenomenon that on the material in the left and right shift, can feed on the guide plate and swing feeding position, to press the right products, finally put the screws fastening.
5、等待产品出来后,如果出现不直或不平,就需要在调直器上进行调整。首先把下轧轮调直到和成型轧轮形成平行线的位置,然后把上轧轮向下轧制产品,看是否能通过或者轧出的材料是否平行,假如不平行或者左右摇摆,可以把调直轧轮上下调整到平行的状态,并且校正在调直器出口处的左右螺丝。
5, wait for the product came out, if not straight or not, you need to make adjustments in the straightening machine. The rolling and forming roller rotation until the form parallel position, and then put on the rolling wheel rolling down products, see if you can pass or rolled material is parallel, if not parallel or swing around, the straightening roller adjusted up and down to the parallel state, and school is adjustable the screw is about straight outlet.
6、切割机的定位尺一般需要放直和放平,它的钳与轧制出来的产品是根据所需要的长度将定位铁进行校正或固定。
6, cutting machine feet to put straight and flat, the clamp and the rolling out of the product according to the required length will be corrected or fixed iron.
友情链接:金彩彩票app  苹果彩票网站  盛兴彩票  财神汇彩票  云顶彩票  云顶彩票网站  环球彩票官网  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!